以FPGA為基礎剛性攻牙控制IC之研製

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：38

、訪客IP：3.21.246.53

姓名

楊學之(Hsueh-Chih Yang) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

以FPGA為基礎剛性攻牙控制IC之研製
(Design and Implementation of an FPGA-based IC for Rigid Tapping)

相關論文

★ 自動平衡裝置在吊扇上之運用	★ 以USB通訊界面實現X-Y Table之位置控制
★ 液體平衡環在立式轉動機械上之運用	★ 液流阻尼裝置設計與特性之研究
★ 液晶電視喇叭結構共振異音研究	★ 液態自動平衡環之研究
★ 抑制牙叉式機械臂移載時產生振幅之設計	★ 立體拼圖式組合音箱共振雜音消除之設計
★ 電梯纜繩振動抑制設計研究	★ 以機器學習導入電梯生產結果預測之研究
★ 新環保冷媒R454取代R410A冷媒迴轉式單缸壓縮機效能分析與可靠性驗證	★ 高速銑削Al7475-T7351的銑削參數與基因演算法研究
★ 自動化鞋型切削機之設計與實現	★ 以FPGA為基礎之精密位置控制IC
★ CNC三維圓弧插補器	★ PID與模糊控制在營建工程自動化的探討

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

以FPGA為基礎剛性攻牙控制IC之研製
研究生：楊學之指導教授：董必正教授
國立中央大學機械工程學系
摘要
本論文以可程式邏輯閘陣列(FPGA)實現可應用於CNC工具機進階功能之剛性攻牙控制的泛用型控制IC，此控制IC包含馬達控制電路、整合PC介面電路、光編碼器電路、馬達驅動訊號電路、D/A介面電路、ISA介面電路與FPGA programming 電路，採高度模組化設計，利用全球通用且跨平台之VHDL硬體描述語言設計。所研製的控制IC具有可程式化的特點，經由相關控制暫存器的設定，即可完成剛性攻牙主軸與Z軸的控制。控制器模組包含位置迴路控制，位置迴路採用具有前饋路徑的比例積分控制架構，取得主軸位置後與Z軸的回授訊號作比較，經由控制器的計算後將控制命令送至Z軸伺服馬達驅動器，控制之命令型態為電壓命令，取樣頻率則為10KHz。此控制IC實現約使用五千個閘數量的FPGA資源，在IC設計驗證方面，本文除了進行硬體電路模擬外，另藉由一組自行設計的D/A介面電路實驗驗證此控制IC的特性，實驗結果顯示所研製的控制IC具有預期的控制性能，且設計的功能皆能正常運作。

摘要(英)

Design and Implementation of an FPGA-based IC for Rigid Tapping
Student: Hsueh-Chih Yang Advisor: Dr. Pi-Cheng Tung
Department of Mechanical Engineering
National Central University
Abstract
This thesis presents the design and implementation of a universal Rigid Tapping control IC using Field Programmable Gate Array (FPGA). The Rigid Tapping is one advanced function of the CNC machine tool. The proposed control IC consists of motor control circuit, PC interface circuit, photo encoder circuit, motor driver circuit, ISA interface circuit and FPGA programming circuit with module design. VHDL will be used to design the IC. The IC which was designed and implemented features of programmability, and we can set the related control registers to control the spindle and Z-axis under Rigid Tapping. The controller accomplishes position loop control. Proportional and integral with feed-forward control is adopted in position loop. Decoding the spindle motor’s position we compare it with the position of Z-axis. The controller will calculate the command and sent the voltage command to the servo motor driver of Z-axis. The sampling rate is 10KHz. Five thousand of the FPGA typical gates were used to realize the proposed control IC. In this thesis, software simulation and a D/A interface circuit have been carried out to verify the functions of the control IC. Experimental results show that the control IC has the control capability and feasibility expectedly and all the designed functions can work correctly.

關鍵字(中)

★ 剛性攻牙
★ 積體電路設計
★ 現場可開發邏輯閘陣列

關鍵字(英)

★ Rigid Tapping
★ IC Design
★ FPGA

論文目次

摘要 I
目錄 II
第一章導論 III
第二章控制器的設計 IV
第三章 FPGA V
第四章以FPGA為基礎剛性攻牙控制IC之實現 VI
第五章系統介紹與實驗結果 VII
第六章結論 VIII
附錄英文論文 IX

參考文獻

[1] L.H Hoang, “Microprocessors and digital IC’s for motion control,” IEEE Proc., vol. 82, no. 8, pp. 1140~1163. Aug. 1994.
[2] V. Oldfield and R. C. Dorf, Field Programmable Gate Arrays, John Wiley & Sonc Inc., 1995.
[3] Panasonic, MINAS-A User Manual, 2002.
[4] Katsuhiko Ogata, “Modern control engineering, 3rd”, pp. 252~254.
[5] Katsuhiko Ogata, “Modern control engineering, 3rd”, pp. 702~703.
[6] Dirk Niggemeyer, Kevin J. Stephano, and Elizabeth M. Rudnick. “Use of a Field Programmable Gate Array for Education in Manufacturing Test and Automatic Test Equipment,” IEEE TRANSACTIONS ON EDUCATION, vol. 44, no. 3, Aug. 2001.
[7] Xilinx, Inc., Databook, 1997.
[8] Altera Corp., UserGuide, 1997.
[9] Xilinx, Inc., Databook, 1997.
[10] Xilinx, Inc., Spartan II Advantage, 2002.
[11] Xilinx, Inc., Spartan II Advantage, 2002.
[12] Xilinx, Inc., Spartan II Advantage, 2002.
[13] Xilinx, Inc., “Foundation Tutorial,” 1997.
[14] Eduarddo Galvan, Antonio Torralba, and Leopoldo G. Franquelo, “ASIC Implementation of a Digital Tachometer with High Precision in a Wide Speed Range,” IEEE, vol. 43, no. 6, Dec. 1996.
[15] John N. Lygouras, Konstantinos A. Lalakos, and Phillipos G. Tsalides, “High-Performance Position Detection and Velocity Adaptive Measurement for Closed-Loop Position Control,” IEEE vol. 47, no. 4, Aug. 1998.
[16] Hewlett-Packard, Optoelectronics Designer’s Catalog, 1993.
[17] Analog Devices, Design-In Reference Manual, 1994.
[18] K.C. Chang, “Digital Systems Design with VHDL and Synthesis”, pp. 177~180.
[19] Yoram Koren McGraw Hill Book Company, “Computer Control of Manufacturing System”,1992.
[20] F. S. Lim, Y. S. Wong, and M. Rahman, “Circular interpolators for numerical control: a comparison of the modified DDA techniques and LSI interpolator,”Comput. Ind., vol 18, pp. 41-52, 1992.
[21] 何丕倫，陳祖型，林育川，「工業控制器定位控制應用技術」，電機月刊，民國八十三年五月。
[22] T. R. Sizer, The Digital Differential Analyzer, Campman & Hall, London,1968.
[23] Xilinx, Inc., “JTAG Programmer Guide”, 2000.
[24] F. Ohkawa, S. Sagara, T. Yamashita and M.Tomizukai, “ Digital adaptive control for servo system with unknown nonlinear friction, ” Industrial Electronics, Control,Instrumentation, and Automation, 1992. Power Electronics and Motion Control.,Proceedings of the 1992 International Conference on , 1992, Vol.3, pp. 1270 –1275
[25] H. Ya ng, J. Yang, J. Zhang and D. Sha, “ Real Time Adaptive Control Algorithm for a VVVF Hydraulic Elevator using Neural Nets, ” American Society of Mechanical Engineers, The Fluid Power and Systems Technology Division (Publication) FPST Fluid Power Systems and Technology Proceedings of the 1997 ASME International Mechanical Engineering Congress and Exposition Nov 16-211997, v 4, 1997.
[26] J. J. Craig, H. Ping and S. S. Sastry, “ Adaptive Control of Mechanical Manipulators, ” The International Journal of Robotics Research, Vol.6, No.2, pp.16-28,1987.
[27] K. Okada and N. Nishimura, “ Noise and vibration reduction technique for
750m/min elevator, ” Mitsubishi Electric ADVANCE, 1994.
[28] N. Mutoh, N. Ohnuma, A. Omiya and M. Konya, “A Motor Driving Controller
Suitable for Elevators, ” Power Electronics, IEEE Transactions on, Vol. 13, Is.6 pp.1123-1134, 1998.

指導教授

董必正(Pi-Cheng Tung)

審核日期

2002-7-9

推文