矽基微柱狀透鏡於光耦合之研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：22

、訪客IP：18.191.162.73

姓名

簡惠君(Hui-Chun Chien) 查詢紙本館藏

畢業系所

光電科學與工程學系

論文名稱

矽基微柱狀透鏡於光耦合之研究

相關論文

★ 富含矽奈米結構之氧化矽薄膜之成長與其特性研究	★ 導波共振光學元件應用於生物感測器之研究
★ 具平坦化側帶之超窄帶波導模態共振濾波器研究	★ 低溫成長鍺薄膜於單晶矽基板上之研究
★ 矽鍺薄膜及其應用於光偵測器之研製	★ 低溫製備磊晶鍺薄膜及矽基鍺光偵測器
★ 整合慣性感測元件之導波矽基光學平台研究	★ 矽基光偵測器研製與整合於光學波導系統
★ 光學滑鼠用之光學元件設計	★ 高效率口袋型LED 投影機之研究
★ 在波長為532nm時摻雜鉬之鈦酸鋇單晶性質研究	★ 極化繞射光學元件在高密度光學讀取頭上之應用研究
★ 不同溫度及波長之摻銠鈦酸鋇單晶性質研究	★ 經氣氛處理之鈦酸鋇單晶其光折變性質及電荷移轉與波長的關係
★ 在不同溫度時氣氛處理鈦酸鋇單晶性質之比較	★ 摻銠鈦酸鋇單晶的氧化還原與光折變性質

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本論文的目的在研究以矽為基板之微柱狀透鏡來提高光學元件間之耦合效率(Coupling Efficiency)，利用在微型光學平台(Micro-Optical Bench，MOB)上，結合半導體製程技術可在矽基板上製作，精確將各元件定位，降低封裝上的誤差。本文所設計出之矽基微柱狀透鏡具有一個維度聚焦能力，將其應用在工作距離約100~200μm之雷射二極體-光纖耦合上。而且利用半導體製程，直接在矽基板上成長蝕刻出透鏡輪廓，具有微小化，低成本且高量產可能性等優點。模擬之光耦合效率在工作距離約100~200μm及不考慮反射損耗(Fresnel Loss)下，約20～40 %，並對元件的製作與系統之量測皆有提出完整的說明及討論。

摘要(英)

The monolithic micro-cylindrical si lens is proposed for increasing
the coupling efficiency between Laser Diode and Single Mode Fiber.
Although the cylindrical lens only has one-dimensional focusing ability,
the coupling efficiency of 20~40% is still designed in the short working
distance of 100~200 μm. By using the micro-optical-bench (MOB)
technology, the optical elements can be precisely aligned on the chip. The
profile is properly defined by the mask, and is fabricated by deep dry
etching. In addition, the strong Fresnel loss is improved by the
anti-reflection coating of SiO2 film. The measurement results show the
highly consistence of the designed structure. In summary, this proposed
coupler module posses the characteristics of minimized, low cost and
high mass production possibility.

關鍵字(中)

★ 耦合效率
★ 透鏡
★ 矽基板
★ 微型光學平台

關鍵字(英)

★ coupling efficiency
★ Silicon-based
★ lens
★ micro-optical-bench

論文目次

摘要 I
目錄 IV
圖目錄 VI
第一章緒論
1-1 前言 1
1-2 微光學系統 3
1-3 論文內容與架構簡介 5
第二章相關理論介紹
2-1 光線追跡法(Ray Tracing) 6
2-2 高斯光傳遞理論 10
2-3 光束傳播法(Beam Propagation Method，BPM) 14
2-4 光纖的耦合 16
第三章矽基微柱狀透鏡之元件設計與分析
3-1 雷射二極體-光纖耦合模組之簡介 22
3-2 矽基微柱狀透鏡應用於光耦合系統之設計概念 26
3-3 設計流程與模擬結果 28
第四章元件製作與量測
4-1 矽基微柱狀透鏡之製作與規格量測 34
4-2 矽基微柱狀透鏡應用在雷射二極體-光纖耦合模組之製作 41
4-3 系統耦合效率之量測 42
4-4 量測結果之分析與討論 48
第五章結論與未來展望 55
參考文獻 56

參考文獻

1. L. Y. Lin, J. L. Shen, S. S. Lee, and M. C. Wu, “Realization of Novel Monolithic Free-Space Optical Disk Pickup Heads by Surface Micromachining," Opt. Lett., 21(2), p. 155-157, 1996.
2. J. Y. Chang, C. M. Wang, C. C. Lee, H. F. Shih, and M. L. Wu, “Realization of Free Space Optical Pickup Head with Stacked Si-Based Phase Element,＂IEEE Photonics Technology Letters, vol. 17, pp. 214-216 , Jan. 2005. SCI/EI
3. Jun-ichi Shimada, Osamu Ohguchi, and Renshi Sawada, ”Microlens Fabricated by the Planar Process,” J. Lightwave Technology, 9, 571-576(1991)
4. Virendra N. Mahajan, Optics imaging and aberrations, SPIE Optical Engineering Press(1998)
5. Joseph M. Geary, Introduction to Lens Design, Willmann-Bell, Inc.(2002)
6. Rsoft Design Group, Beam Prop 5.1.1 Manual, Rsoft Design Group, Inc.(1993-2003)
7. Frank L. Pedrotti, Leno S. Pedrotti, Introduction to Optics, (Prentice-Hall, 1987)
8. 李俊叡, 鼓形透鏡用於單模光纖收發器之設計, (中央大學光電所碩士論文, 台灣, 2003)
9. B. E. A. Saleh, and M. C. Teich, Fundamentals of Photonics, John Wiley (1991).
10. J. W. Goodman , “ Introduction to Fourier Optics” , McGraw-Hill , p.32 (1996)
11. A. Yariv, and P. Yeh, “Optical Waves in Crystals” , Mei Ya, 1984.
12. 藍孝晉, Grismlens複合式分波多工器系統, 中央大學光電科學研究所碩士論文, 2004
13. code V Technology note, BPR Diffraction-based Beam Propagation, (Optical Research Associates, America)
14. ASAP Technical Guide, Breault Research Organization, Inc.
15. Y. Aoki, T. Kato, R. J. Mizuno and K. Iga, “Miro-optical bench for alignment-free optical coupling,” Appl. Opt., 38, p. 963-965, 1999.
16. Amnon Yariv, Optical Electronics in modern communications, New York : Oxford University Press(1997)
17. I. Moerman, P. P. Van Daele, and P. M. Demeester, “A review on fabrication technologies for the monolithic integration of tapers with III-V semiconductor devices, ” IEEE J. Select. Topics Quant. Electron., 3, 1308, 1997.
18. K. Shiraishi, and N. Hiraguri, “A lensed fiber with cascaded GI-fiber configuration for efficient coupling between LDs to single-mode fibers,” ECOC’98, 20-24, 355, 1998.
19. K. Shiraishi and S. I. Kuroo, “A new lensed-fiber configuration employing cascaded GI-fiber chips,” J. Lightwave Technol., 18, 787, 2000.
20. S. K. Mondal, S. Gangopadhyay, and S. Sarkar, “Analysis of an upside-down
21. B. Hubner, G. Vollrath, R. Ries, C. Greus, H. Janning, E. Ronneberg, E. Kuphal, B. Kempf, R. Gobel, F. Fiedler, R. Zengerle, and H. Burkhard, “Laser diodes with integrated spot-size transformer as low-cost optical transmitter elements for telecommunications, ” IEEE J. Select. Topics Quant. Electron., 3, 1372, 1997.
22. G. A. Vawter, R. E. Smith, H. Hou, and J. R. Wendt, “Semiconductor laser with tapered-rib adiabatic-following fiber coupler for expanded output-mode diameter, ” IEEE Photon. Technol. Lett., 9, 425, 1997.
23. X. Yan, M. L. Masanovic, E. J. Skogen, Z. Hu, D. J. Blumenthal, and L. A. Coldren, “Optical mode converter integration with InP-InGaAsP active and passive waveguides using a single regrowth process, ” IEEE Photon. Technol. Lett., 14, 1249, 2002.
24. T. Wongcharoen, B. M. A. Rahman, M. Rajarajan, and K. T. V. Grattan, “Spot-size conversion using uniform waveguide sections for efficient laser-fiber coupling, ” J. Lightwave Technol., 19, 708, 2001.
25. K. Shiraishi, and N. Hiraguri, “A lensed fiber with cascaded GI-fiber configuration for efficient coupling between LDs to single-mode fibers,” ECOC’98, 20-24, 355, 1998.
26. K. Shiraishi and S. I. Kuroo, “A new lensed-fiber configuration employing cascaded GI-fiber chips,” J. Lightwave Technol., 18, 787, 2000.
27. S. K. Mondal, S. Gangopadhyay, and S. Sarkar, “Analysis of an upside-down taper lens and from a single-mode step-index fiber,” Appl. Opt., 37, 1006, 1998.
28. R. P. Ratowsky, L. Yang, R. J. Deri, K. W. Chang, J. S. Kallman, and G. Trott, “Laser diode to single-mode fiber ball lens coupling efficiency: full-wave calculation and measurements,” Appl. Opt., 36, 3435, 1997.
29. M. Sumida, and K. Takemoto, “Lens aberration effect on a laser-diode-to-single-mode-fibre coupler,” Electron. Lett., 18, 586, 1982.
30. R. G. Wilson, “Ball-lens coupling efficiency for laser-diode to single-mode fiber： comparison of independent studies by distinct methods,” Appl. Opt., 37, 3201, 1998.
31. Y. Fu, and N. K. A. Bryan, “Hybrid microdiffractive-microrefractive lens with a continuous relief fabricated by use of focused-ion-beam milling for single-mode fiber coupling, ” Appl. Opt., 40, 5872, 2001.
32. Jun-ichi Shimada, Osamu Ohguchi, and Renshi Sawada, “Focusing Characteristics of a Wide-Striped Laser Diode Integrated with a Microlens,” J. Lightwave Technology, 12, 936-942(1994)
33. Jun-ichi Shimada, Osamu Ohguchi, and Renshi Sawada, ”Microlens Fabricated by the Planar Process,” J. Lightwave Technology, 9, 571-576(1991)
34. 10J. M. Bennett and L. Mattsson, Introduction to Surface Roughness and Scattering (Optical Society of America, Washington, DC, 1989).

指導教授

張正陽(Jeng-Yang Chang)

審核日期

2006-7-25

推文