在不同氣氛下Al-XMg(X=2,4wt%)
熱合氧化膜的成長機制

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：16

、訪客IP：3.133.107.11

姓名

吳俊逸(Yi-chun WU) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

在不同氣氛下Al-XMg(X=2,4wt%) 熱合氧化膜的成長機制
(Thermally-Formed Oxide on Al-XMg(X=2,4wt%) Alloys in different atmosphere )

相關論文

★ 7005與AZ61A拉伸、壓縮之機械性質研究	★ 雷射去除矽晶圓表面分子機載污染參數的最佳化分析
★ 球墨鑄鐵的超音波檢測	★ 模具溫度對TV前框高亮光澤產品研討
★ 高強度7075-T4鋁合金之溫間成形研究	★ 鎂合金燃燒、鑽削加工與表面處理之研究
★ 純鈦陽極處理技術之研發	★ 鋁鎂合金陽極處理技術之研發
★ 電化學拋光處理、陽極處理中硫酸流速與封孔處理對陽極皮膜品質之影響	★ 電解液溫度與鋁金屬板表面粗糙度對陽極處理後外觀的影響
★ 製程參數對A356鋁合金品質的影響及可靠度的評估	★ 噴砂與前處理對鋁合金陽極皮膜品質的影響
★ 鎂合金回收重溶之品質與疲勞性質分析	★ 鋁合金熱合氧化膜與陽極氧化膜成長行為之研究
★ 潤滑劑與製程參數對Al-0.8Mg-0.5Si鋁合金擠壓鑄件的影響	★ 摩擦攪拌製程對AA5052鋁合金之微觀組織及對陽極皮膜的影響

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本研究主要在探討鋁鎂合金熱成長氧化膜的分析，使用的材料有靶材鋁-2wt%鎂、鋁-4wt%鎂兩種。試片裁切成10 mm × 10 mm × 6 mm的大小，使用400號、800號、1200號、1500號跟2000號砂紙將表面乾磨，然後放在加熱爐中分別在空氣及氮氣下加熱到500℃，持溫1小時、6小時、25小時以生長氧化膜。
實驗結果發現，由於氧化鎂自由能低於氧化鋁，漸漸地而氧化膜的表面富含氧及鎂，表層變成以鎂的氧化物為主，所以鋁鎂合金在氣氛為空氣的加熱過程中其表面的氧化層主要以鎂的氧化物為主。鋁-2wt%鎂的氧化膜有氧化鋁、氧化鎂及尖晶石相的出現，鋁-4wt%鎂的氧化膜並沒有觀察到尖晶石相的產生，可知尖晶石相的產生取決於鋁鎂合金中的鎂含量。
氣氛為氮氣的加熱過程中其表面的氧化膜主要以鎂及鋁的氮化物為主在加熱過程中因為表層富含鎂，鎂會與氮氣反應形成Mg3N2的化合物，Mg3N2再與基材中的鋁反應形成AlN，生成AlN的量合金中的鎂含量有關，隨著加熱時間的增長氮氣中微量的氧會與Mg3N2及AlN反應成MgO與Al2O3。

摘要(英)

The purpose of this study is analyzing the thermal-formed oxide on aluminum and magnesium alloys. Two materials, Al-2wt%Mg、Al-4wt%Mg were used in this study. The cube samples were prepared in 10 mm × 10 mm × 6 mm. They were then polished by ＃400, ＃800, ＃1200, ＃1500 and ＃2000 abrasive paper. These cube samples were moved to the muffle furnace in the air and nitrogen separately and then heated to 500℃ and hold on for 1 hr,6hrs,25hrs.
The experimental result find that the magnesium oxide and Gibbs-free energy are lower than the alumina, and the oxide film gradually is rich in oxygen and magnesium, the surface oxide layer which almost entirely magnesium oxide, so Al-Mg alloy oxide film is mainly the magnesium oxide for heating of air. The Al-2wt%Mg thermal oxide film appearance with alumina, MgO, MgAl2O4 spinel, and MgO appeared first on the surface of the sample and followed by formation MgAl2O4 spinel. The Al-2wt%Mg thermal oxide film doesn’t observe MgAl2O4 spinel, to transform MgAl2O4 spinel is depend on the content of Mg of Al-Mg alloy.
When Al-Mg alloy heat in the nitrogen, the surface is formed aluminum nitride and magnesium nitride, Mg react with nitrogen to form Mg3N2, then react and form AlN with aluminum. Formulation amount of the AlN is related to content of Mg of Al-Mg alloy. During long heat of time with nitrogen, the deleterious effect of oxygen impurities is due to its inhibition to the chemisorbtion of N2 molecules, then Mg3N2 and AlN transform to MgO and Al2O3 separately.

關鍵字(中)

★ 熱合氧化膜
★ 尖晶石
★ AlN
★ Mg3N2

關鍵字(英)

★ AlN and Mg3N2
★ spinel
★ thermal oxide film

論文目次

中文摘要…………………………………………………………… I
Abstract…………………………………………………………… II
總目錄……………………………………………………………… III
表目錄……………………………………………………………… VI
圖目錄……………………………………………………………… VII
第一章前言……………………………………………………… 1
第二章文獻回顧………………………………………………… 2
2.1 鋁合金的簡述………………………………………………… 2
2.1.1 鋁合金的類型……………………………………………… 2
2.1.2 鑄造用鋁合金的分類……………………………………… 2
2.1.3 純鋁(1XX.X)……………………………………………… 3
2.1.4 影響熔湯表面張力的元素………………………………… 3
2.2 氧化鋁的生成………………………………………………… 3
2.2.1 氧化鋁的種類……………………………………………… 3
2.2.2 氧化鋁的形成……………………………………………… 5
2.2.3 化學分析電子儀(ESCA)診斷氧化鋁膜…………………… 7
2.3 鋁鎂合金……………………………………………………… 8
2.3.1 鋁鎂(5XX.X)……………………………………………… 8
2.3.2鋁鎂合金特性……………………………………………… 8
2.3.3 鎂元素對鋁合金的影響…………………………………… 9
2.4 氮化鋁的生成………………………………………………… 9
2.4.1 氮化鋁的結構與特性……………………………………… 9
2.4.2 氮化鋁的形成……………………………………………… 10
2.5 MgAl2O4的生成……………………………………………… 11
2.5.1 MgAl2O4的結構與特性…………………………………… 11
2.5.2 MgAl2O4的形成…………………………………………… 12
2.6 表面吸附……………………………………………………… 12
2.6.1 物理吸附與化學吸附……………………………………… 12
2.6.2 氮氣與氧氣在表面吸附的情形…………………………… 13
第三章實驗方法與步驟………………………………………… 14
3.1 實驗目的……………………………………………………… 14
3.2 實驗材料……………………………………………………… 14
3.2.1 鋁鎂合金…………………………………………………… 14
3.3 試片規格……………………………………………………… 14
3.4 實驗設備……………………………………………………… 14
3.5 實驗步驟……………………………………………………… 16
3.5.1 鋁鎂合金固溶處理………………………………………… 16
3.5.2 氧化膜生長………………………………………………… 16
第四章結果與討論……………………………………………… 17
4.1 Al-2Mg氧化膜………………………………………………… 17
4.1.1 試片表面處理……………………………………………… 17
4.1.2 Al-2Mg試片的TGA檢測…………………………………… 17
4.1.3 Al-2Mg試片的XRD檢測…………………………………… 17
4.1.4 掃描式電子顯微鏡(SEM)的觀察………………………… 18
4.1.5 化學分析電子儀(ESCA)的檢測…………………………… 18
4.1.6 電子控針微分析儀(EPMA)的檢測………………………… 18
4.2 Al-4Mg氧化膜………………………………………………… 19
4.2.1 試片表面處理……………………………………………… 19
4.2.2 Al-4Mg試片的TGA檢測…………………………………… 19
4.2.3 Al-4Mg試片的XRD檢測…………………………………… 19
4.2.4 掃描式電子顯微鏡(SEM)的觀察………………………… 20
4.2.5 化學分析電子儀(ESCA)的檢測…………………………… 20
4.2.6 電子控針微分析儀(EPMA)的檢測………………………… 20
4.2.7 Al-2、4Mg氧化膜討論…………………………………… 21
4.3 在氮氣氣氛下的Al-2Mg氧化膜……………………………… 22
4.3.1 試片表面處理……………………………………………… 22
4.3.2 Al-2Mg試片的TGA檢測…………………………………… 22
4.3.3 Al-2Mg試片的XRD檢測…………………………………… 22
4.3.4 掃描式電子顯微鏡(SEM)的觀察………………………… 23
4.4 在氮氣氣氛下的Al-4Mg氧化膜……………………………… 24
4.4.1 試片表面處理……………………………………………… 24
4.4.2 Al-4Mg試片的TGA檢測…………………………………… 24
4.4.3 Al-4Mg試片的XRD檢測…………………………………… 24
4.4.4 掃描式電子顯微鏡(SEM)的觀察………………………… 25
4.4.5 氮氣氣氛下Al-2、4Mg氧化膜討論……………………… 25
4.5 綜論…………………………………………………………… 26
第五章結論……………………………………………………… 27
參考文獻…………………………………………………………… 28

參考文獻

1. R. A. Robie, B. S. Hemingway, J. R. Fisher, Thermodynamics Properties of Minerals and Related Substances at 298.15 K and 1 Bar (105 Pascal) pressure and at Higher Temperature, U.S. Government Printing Office, Washington, 1978 p.137-248
2. I. J. Polmear, Light Alloys：Metallurgy of the Light Metals, 3rd ed., John Wiley & Sons, New York, 1995
3. C. R. Loper, Jr., “Fluidity of Aluminum－Silicon Casting Alloys, AFS Transactions”, 100 (1992) 533-538.
4. P. S. Santos, H. S. Santos, S. P. Toledo, “Standard Transition Aluminas. Electron Microscopy Studies”, Materials Research, 3 (2000) 104-114.
5. S. W. Whangbo, Y. K. Choi, W. S. Koh, K. B. Chung, H. K. Jang, C. N. Whang, “Effect of Silicon Surface States on the Properties of Epitaxial Al2O3 Films”, Thin Solid Films, 398-399 (2001) 480-484.
6. L. D. Hart, Esther Lense, Alumina Chemicals：Science and Technology Handbook, American Ceramic Society, Westerville, Ohio, 1990, p.32, 50
7. William D. Callister, Jr., Materials Science and Engineering：An Introduction, 4th ed, John Wiley & Sons, New York, 1997, p.38.
8. M. R. Alexander, G. E. Thompson, G. Beamson, “Characterization of the Oxide/Hydroxide Surface of Aluminum Using X-ray Photoelectron Spectroscopy： A Procedure for Curve Fitting the O 1s Core Level”, Surface and Interface Analysis, 29 (2000) 468-477.
9. 林敬二、楊美惠、楊寶旺、廖德章、薛敬和，英．中．日化學大辭典，高立圖書有限公司，台北，2000，p.70、380、927、1364
10. W. D. Kingery, H. K. Bowen, D. R. Uhlmann, Introduction to Ceramics, 2nd ed, Wiley, New York, 1976, p.64, 65
11. I. Levin, D. Brandon, “Metastable Alumina Polymorphs：Crystal Structures and Transition Sequences”, Journal of the American Ceramic Society, 81 (1998) 1995-2012.
12. 宋啟瑞，在鋁上成長堰層陽極氧化膜的研究，國立交通大學材料科學與工程研究所碩士班論文，新竹，民國九二年七月
13. Per Kofstad, High Temperature Oxidation of Metals, John Wiley & Sons, New York, 1966
14. 徐東明，熱成長氧化膜防治S44660不銹鋼氫脆之研究，國立中興大學材料工程學研究所碩士班論文，台中，民國八八年七月
15. P. E. Doherty, R.S. Davis, “Direct Observation of the Oxidation of Aluminum Single-Crystal Surfaces”, Journal of Applied Physics, 34 (1963) 619-628.
16. P. E. Doherty, R.S. Davis, “The Formation of Surface Pits by the Condensation of Vacancies”, Acta Metallurgica, 7 (1959) 118-123.
17. L. P. H. Jeurgens, W. G. Sloof, F. D. Tichelaar, E. J. Mittemeijer, “Composition and Chemical State of the Ions of Aluminium-Oxide Films Formed by Thermal Oxidation of Aluminum”, Surface Science, 506 (2002) 313-332.
18. P. C. Snijders, L. P. H. Jeurgens, W. G. Sloof, “Structure of Thin Aluminium-Oxide Films Determined From Valence Band Spectra Measured Using XPS”, Surface Science, 496 (2002) 97-109.
19. O. Salas, H. Ni, V. Jayaram, K. C. Vlach, C. G. Levi, R. Mehrabian, “Nucleation and Growth of Al2O3/metal Composites by Oxidation of Aluminum Alloys”, Journal of Materials Research, 6 (1991) 1964-1981.
20. S. W. Whangbo, Y. K. Choi, H. K. Jang, Y. D. Chung, I. W. Lyo, C. N. Wang, “Effect of Oxidized Al Prelayer for the Growth of Polycrystalline Al2O3 Films on Si Using Ionized Beam Deposition”, Thin Solid Films, 388 (2001) 290-294.
21. R.E Sanders, Jr., Aluminum Alloys-Contemporary Research and Applications, ed By A.K. Vasudevan and R.D Doherty, Academic press(1989), 66.
22. R.E Sanders, Jr., Aluminum Alloys-physical and Mechanical Properties, (1986), pp.1441-1484
23. James H. Edgar and W. J. Meng: ”Chapter 1-3 Crystal structure, mechanical
properties, thermal properties and refactive index of AIN”, Properties of Group ш Nitrides,1993.
24. Bernard Gil and Fernando A. Ponce: “Chapter 4 Structural Defects and Materials Performance of the ш-v Nitrides”, Group ш Nitride Semiconductor Compounds Physics and Applications, 1998, P. 124, P. 127, P. 197.
25. C. Morosanu, T. A. Stoica, T. F. Stoica, D. Necsoiu and M. Popescu: “Optical, Electrical and structural properties of AIN thin films”, IEEE, 1995, P. 193-186.
26. C. Caliendo G. Saggio, P. Verardi, E. Verona: “Piezoelectric AIN Film for SAW Devices Application”, IEEE Ultrasonics symposium, 1993, P. 49-252.
27. F. S. Hickernell and H. M. liaw: “The Structural and Acoustic Properties of Sputtered Aluminum Nitried on Silicon”, IEEE, 1995, P.543-546.
28. Q. Zheng, R. G. Reddy” Mechanism of in situ formation of AlN in Al melt using nitrogen gas”, Journal of Materials Science 39 (2004) 141– 149
29. Qingjun Zheng and Ramana G. Reddy,”Influence of Magnesium on Nitridation of Molten Aluminum from Nitrogen Bubbling Gas”, High Temperature Materials and Processes (2003) 63-71
30. Qinghua Hou , Raj Mutharasan , Michael Koczak ,” Feasibility of aluminium nitride formation in aluminum alloys”, Materials Science and Engineering A195 (1995) 121-129
31. H.Z. Ye, X.Y. Liu, Ben Luan, “In situ synthesis of AlN in Mg–Al alloys by liquid nitridation”, Journal of Materials Processing Technology 166 (2005) 79–85
32. Yu Huashuna, J.D. Kim, S.B. Kang, “The formation of AlN and TiN particles during nitrogen bearing gas injection into Al–Mg–Ti melt”, Materials Science and Engineering A 386 (2004) 318–325
33. 余樹楨, “晶體之結構與性質” (民國85 年11 月) 國立編譯館.
34. E. A. Marguire Jr., R. L. Gentilman, “Press forging small domes of spinel”,American Ceramic Society Bulletin, Vol.60 (1981) pp.255..
35. D. W. Roy, J. L. Hastert, “Polycrystalline MgAl2O4 spinel for high temperature windows”, Ceramic Engineering and Science Proceedings Vol.4 (1983) pp.502.
36. Vinay Kumar Singh, Rakesh Kumar Sinha, “Low temperature synthesis of spinel ( MgA12O4)”, Materials Letters 3 1 (1997) 28l-285
37. Jafar F. Al-Sharab and Frederic Cosandey, “TEM Characterization of Nanostructured MgAl2O4 Synthesized by a Direct Conversion Process from γ-Al2O3” J. Am. Ceram. Soc., 89 [7] 2279–2285 (2006)
38. V. Kevorkijan, T. Kosmac and K. Kristoffer, ” Sponaneous Reactive Infiltration of Porous Ceramic Preforms with Al–Mg and Mg in the Presence of Both Magnesium and Nitrogen—New Experimental Evidence”, Materials and Manufacturing Process, 17(3), 307–322 (2002)
39. W. Adamson and Alice P. Gast ,” Physical chemistry of surfaces(1997)”
40. 29. S . Porowski, MRS Inter. J. Nitride Semi. Re. 4S1 (1999) G10.2.

指導教授

施登士(Teng-Shih Shih)

審核日期

2007-7-24

推文