電化學放電加工硼矽玻璃之微流道成形技術研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：28

、訪客IP：18.190.219.178

姓名

鄭偉欣(Wei-Hsin Cheng) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

電化學放電加工硼矽玻璃之微流道成形技術研究
(A Study on the Microchannel Machinability of Pyrex Glass by Using Electrochemical Discharge Machining)

相關論文

★ 運用化學機械拋光法於玻璃基板表面拋光之研究	★ 電泳沉積輔助竹碳拋光效果之研究
★ 凹形球面微電極與異形微孔的成形技術研究	★ 運用電泳沉積法於不鏽鋼鏡面拋光之研究
★ 電化學結合電泳精密拋光不銹鋼之研究	★ 純水中的電解現象分析與大電流放電加工特性研究
★ 結合電化學與電泳沉積之微孔複合加工研究	★ 放電加工表面改質與精修效果之研究
★ 汽車熱交換器用Al-Mn系合金製程中分散相演化及再結晶行為之研究	★ 磁場輔助微電化學銑削加工特性之研究
★ 磁場輔助微電化學鑽孔加工特性之研究	★ 微結構電化學加工底部R角之改善策略分析與實做研究
★ 加工液中添加Al-Cr混合粉末對工具鋼放電加工特性之影響	★ 不同加工液（煤油、蒸餾水、混合液）對鈦合金（Ti-6Al-4V）放電加工特性之影響
★ 放電與超音波振動複合加工添加TiC及SiC粉末對Al-Zn-Mg系合金加工特性之影響	★ 添加石墨粉末之快速穿孔放電加工特性研究

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

近年來電化學放電加工(Electrochemical Discharge Machining, ECDM)被運用於加工非導體脆硬材料，而且已經證實可對Pyrex玻璃進行三維微結構的加工。不過，現今利用電化學放電進行微銑削加工卻無法有效的控制加工精度。因此本文以脈衝電壓取代直流電壓、電極轉速與水平加工進給率為參數，在Pyrex玻璃上進行微流道的加工，並探討加工後微流道的形狀及尺寸精度及其對於加工特性之影響。
實驗結果顯示，將直流波形能量加工改以脈衝能量輸入(40 V，Ton：Toff = 2ms：2ms)，並結合電極的旋轉(1500 rpm)，能使加工後的微溝槽具有最佳的改善效果。最後利用掃描式銑削加工法進行高深寬比之微溝槽與複雜三維微結構加工的可行性探討，結果發現加工後之微溝槽與三維結構具有極高的尺寸精度，並證明了電化學放電加工可真實應用於Pyrex玻璃上製作三維微結構之可行性。

摘要(英)

Electrochemical discharge machining (ECDM) is demonstrated to be a potential process for 3D-microstructuring of Pyrex glass. However, it is difficult to obtain an accurate machining shape with a good surface quality because it is difficult to control the discharge characteristics near the tool tip. To improve the machining quality of the ECDM micromilling process, microgroove machining experiments were conducted in this study. Three factors affecting ECDM micromillimg performance, pulse voltage, rotational rate of tool and feed velocity of tool were taken up as machining parameters to investigate their influences on machining performance.
The results indicate that optimum combinations of both pulse voltage (40V, Ton：Toff = 2 ms：2 ms) and rotational speed (1500 rpm) will realize better machining accuracy. The feasibility of 3-dimensional microstructure machining was demonstrated by a layer-by-layer ECDM micromilling machining. Complex structures were made to demonstrate the great potential for the 3D microstructuring of Pyrex glass of the ECDM micromilling process.

關鍵字(中)

★ 三維微結構
★ 脈衝電壓
★ 微流道
★ Pyrex玻璃
★ 電化學放電加工

關鍵字(英)

★ microgroove
★ pulse voltage
★ Pyrex glass
★ 3D-microstructuring
★ ECDM

論文目次

摘要 I
Abstract II
總目錄 III
圖目錄 V
表目錄 VII
第一章緒論 1
1-1 研究動機 1
1-2 文獻回顧 4
1-2-1電化學放電加工機制文獻 4
1-2-1電化學放電加工特性文獻 4
1-3 研究目的 7
第二章基本原理 8
2-1 ECDM系統基本配置 8
2-2 ECDM的電化學反應[3] 10
2-3 ECDM的放電火花形成過程[4] 12
2-4 ECDM的材料去除機制 14
2-5 線放電研磨加工原理 17
第三章實驗材料、設備與步驟 21
3-1 實驗材料 21
3-2 實驗設備 25
3-3 實驗流程 36
3-4 實驗參數設定 37
3-5 實驗步驟 38
3-5-1 碳化鎢電極整修 38
3-5-2 電解液之調配 41
3-5-3 ECDM機構設備的調整 41
3-5-4 微流道加工方法 41
3-5-5 輸入不同實驗參數值 42
3-5-6 三維結構應用 42
3-5-7 試片清洗 42
3-5-8 微流道形態之觀察與測量 42
第四章結果與討論 43
4-1 脈衝型態能量輸入對ECDM微流道加工的影響 45
4-2 不同電極轉速對ECDM微流道加工的影響 52
4-3 不同進給速率對ECDM微流道加工的影響 56
4-4 加工不同深度對ECDM微流道的影響 61
4-4-1 深切加工微流道 61
4-4-2 掃描進給加工微流道 64
4-5 3D微結構應用 69
第五章結論 71
第六章參考文獻 72
個人簡歷 75

參考文獻

1. H. Kurafuji and K. Suda, Electrical discharge drilling of glass, Annals of the CIRP, 16 415 (1968).
2. I. Basak and A. Ghosh, Mechanism of spark generation during electrochemical discharge machining: a theoretical model and experimental verification, Journal of Material Processing Technology, 62 46 (1996).
3. B. Bhattacharyya, B. N. Doloi and S. K. Sorkhel, Experimental investigations into electrochemical discharge machining (ECDM) of non-conductive ceramic materials, Journal of Materials Processing Technology, 95 145 (1999).
4. C. T. Yang, S. S. Ho and B. H. Yan and F. Y. Huang, Micro hole machining of borosilicate glass trough electrochemical discharge machining (ECDM), Key Engineering Materials, 196 149 (2001).
5. V. Fascio, H. H. Langen, H. Bleuler and Ch. Comninellis, Investigations of the spark assisted chemical engraving, Electrochemistry Communications, 5 203 (2003).
6. V. K. Jain, P. S. Rao, S. K. Chowdhury and K. O. Rajurkar, Experimental investigations into wire electrochemical spark machining (TW-ECSM), Trans. ASME Journal of Engineering of Industry, 113 75 (1991).
7. H. Langen, J. M. Breguet, H. Bleuler, Ph. Renaud and T. Masuzawa, Micro electrochemical discharge machining of glass, International Journal of Electrical Machining, 3 65 (1998).
8. R. Wüthrich, V. Fascio, D. Viquerat and H. Langen, In situ measurement and micro-machining of glass, International Symposium on Micro-mecatronics and Human Science (MHS’99), Nagoya, 185 (1999).
9. H. Langen, I. Ceausoglu, M. van der Meer, E. Lehmann, H. Bleuler and Ph. Renaud, Electrochemical micromachining of glass using Mico- EDMed Microtools, Proceedings of Ultraprecision in Manufacturing Engineering, 26–30 May Braunsweig, 672 (1997).
10. R. Wüthrich, V. Fascio and D. Viquerat and H. Langen, Study of spark assisted chemical engraving-process technology date, International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN) 1 Einhoven, 265 (2002).
11. D. J. Kim, Y. Ahn, S. H. Lee and Y. K. Kim, Voltage pulse frequency and duty ratio effect in an electrochemical discharge microdrilling process of Pyrex glass, International Journal of Machine Tools & Manufacture, 46 1064 (2005).
12. R. Wüthrich, K. Fujisaki, Ph. Couthy, L. A. Hof and H. Bleuler, Spark assisted chemical engraving (SACE) in microfactory, Journal of Micromechanics and Microengineering, 15 S276 (2005).
13. R. Wüthrich, L. A. Hof, A. Lal, K. Fujisaki, H. Bleuler, Ph. Mandin and G. Picard, Physical principles and miniaturization of spark assisted chemical engraving (SACE), Journal of Micromechanics and Microengineering, 15 S268 (2005).
14. R. Wüthrich, U. Spaelter, Y. Wu and H. Bleuler, A systematic characterization method for gravity-feed micro-hole drilling in glass with spark assisted chemical engraving (SACE), Journal of Micromechanics and Microengineering, 16 1891 (2006).
15. R. Wüthrich, B. Despont, P. Maillard and H. Bleuler, Improving the material removal rate in spark-assisted chemical engraving (SACE) gravity-feed micro-hole drilling by tool vibration, Journal of Micromechanics and Microengineering, 16 N28 (2006).
16. C. T. Yang, S. L. Song, B. H. Yan and F. Y. Huang, Improving machining performance of wire electrochemical discharge machining by adding SiC abrasive to electrolyte, International Journal of Machine Tools＆Manufacture, 496 2044 (2006).
17. B. H. Yan, C. T. Yang, F. Y. Huang and Z. H. Lu, Electrophoretic deposition grinding (EPDG) for improving the precision of microholes drilled via ECDM, Journal of Micromechanics and Microengineering, 17 376 (2007).
18. Z. P. Zheng, H. C. Su, F. Y. Huang and B. H. Yan, The tool geometrical shape and pulse-off time of pulse voltage effects in a Pyrex glass electrochemical discharge microdrilling process, Journal of Micromechanics and Microengineering, 17 265 (2007) .
19. 王家威著，界面活性劑改散玻璃微孔電化學放電成形精度的影響，國立中央大學碩士論文，2006。

指導教授

顏炳華(Biing-Hwa yan)

審核日期

2007-7-2

推文