加工參數對 A1050P板材經壓延加工後的曲率變化之實驗研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：94

、訪客IP：18.191.66.102

姓名

江龍(Lung Chiang) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

加工參數對 A1050P板材經壓延加工後的曲率變化之實驗研究
(Experimental research of working parameter effect curvature behavior of rolling aluminum A1050P)

相關論文

★ 中尺寸LED背光模組之實驗研究	★ 利用有限元素法與反應曲面法探討金屬成型問題之最佳化設計-行星路徑旋轉鍛造傘齒輪為例
★ 以反應曲面法進行行動電話卡勾之最佳化設計	★ 以微分式內涵塑性理論分析材料受軸向循環負載之塑性行為
★ A1070在累進式背擠製下的機械性質與微結構之研究	★ 超音波輔助沖壓加工之應用-剪切、引伸與等通彎角擠製
★ 應用多體動力學於具循環氣體負載之迴轉式壓縮機振動預測模型建立	★ 以有限元素法與反應曲面法分析螺旋傘齒輪之旋轉鍛造最佳化設計
★ 超音波振動輔助鋁合金6061及低碳鋼S15C拉伸試驗之研究	★ 旋轉鍛造螺旋齒輪製程分析
★ 等通道扭轉彎角擠製之有限元素法及反應曲面法分析	★ 以有限元素法與反應曲面法分析增量式板金成形
★ 以有限元素法與反應曲面法分析螺旋傘齒輪之雙錐輥旋轉鍛造最佳化設計	★ 以有限元素法與反應曲面法分析兩點增量成形
★ 引伸成形加工問題之有限元素分析	★ 應用流函數法分析軸對稱熱擠製加工問題

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本文主要是利用實驗探討試片經非對稱壓延加工後，其試片的輥輪壓延力、壓延扭矩及彎曲曲率分別於不同縮減率時的變化情形。實驗條件以同徑異周速為主，包含輥輪與壓延試片間的界面摩擦及入口試片厚度不同等。
藉由本實驗所規劃的加工條件，可得知壓延後之試片曲率受縮減率大小、圓周切線速度不同步、界面摩擦及試片初始厚度不同等條件的影響，試圖找出曲率值介於±0.0025(1/mm)內的臨界縮減率（即壓延後的成形試片呈現接近平坦的狀態）產生的條件。藉以達到曲率控制，減少壓延道次，以期達到加工能量需求較低之經濟性製程。

摘要(英)

This paper discusses rolling force, rolling torque and curvature ratio with different reduction at asymmetrical rolling. The experimental conditions include different flat thickness and interface between rolling and specimens by lubrication or dry friction.
By experimental conditions can find out specimens that become curvature turn up or turn down behavior with different reduction, different rolling speed, interface friction and different flat thickness after rolling process. Try to find out the critical reduction that curvature between ±0.0025(1/mm), i.e. curvature is near zero. For the purpose of control the curvature and decrease rolling pass times that can reach lower economical production process.

關鍵字(中)

★ 曲率
★ 壓延
★ 縮減率

關鍵字(英)

★ curvature
★ rolling
★ reduction

論文目次

中文摘要 I
英文摘要 II
致謝 III
目錄 IV
圖目錄 VI
表目錄 IX
第一章緒論 1
1-1 前言 1
1-2 板材非對稱壓延 2
1-3 研究動機 3
第二章實驗基礎 4
2-1 壓延種類 4
2-2 文獻回顧 5
2-2-1 實驗研究方面 5
2-2-2 理論解析方面 7
第三章實驗設備與方法 10
3-1 實驗設備 10
3-1-1 壓延機 10
3-1-2 資料擷取系統 10
3-2 實驗方法 11
3-2-1 試片準備 11
3-2-2 實驗條件 12
3-2-3 編號的表示意義 12
3-2-4 潤滑條件 13
3-2-5 輥輪與工作平台調整 13
3-2-6 壓延實驗步驟 15
3-3 成形板材之曲率量測 16
3-3-1 曲率計之測定原理 16
3-3-2 曲率量測方法之探討 17
3-3-3 曲率計之校正 18
3-4 拉伸試驗 18
3-5 環壓試驗 20
3-6 Forward Slip 22
第四章結果與討論 25
4-1 拉伸試驗 25
4-2 環壓試驗 26
4-3 Forward Slip 27
4-4 同徑壓延實驗 27
4-4-1 壓延力及壓延扭矩之比較 30
4-4-2 周速比對壓延試片曲率的效應 31
4-4-3 試片厚度對壓延試片彎曲曲率的影響 36
4-4-4 界面摩擦條件對試片彎曲曲率的影響 40
第五章結論 43
參考文獻 46
附錄 79

參考文獻

[1] T. Von Karman, Zeitschrift fur angewandte Mathematik und Mechanik, 5 (1941-1942) 139.
[2] E. Orowan, "The Calculation of Roll Pressure in Hot and Cold Flat Rolling", Proceedings of the Institution of Mechanical Engineers, 150 (1943) 140-167.
[3] D. R. Bland, and H. Ford, "The Calculation of Roll Force and Torque in Cold Strip Rolling with Tensions," Proc. Instn. Mech. Engrs., 159 (1948) 144-153.
[4] H. Ford, F. Ellis, and D. R. Bland, "Cold Rolling with Strip Tension Part I. A New Approximate Method of Calculation and a Comparison with Other Method", Jounal of the Iron and Steel Institute, (May 1951) 57-72.
[5] R. B. Sims, "The Calculation of Roll Force and Torque in Hot Rolling Mills", Proc. Instn. Mech. Engrs., 168 (1954) 191-200
[6] J.M. Alexander, "On the Theory of Rolling", Proceedings of the Royal Socity of London. Series A., 326 (1972) 535-563.
[7] D. Rusia, "Improvements to Alexander's Computer Model for Force and Torque Calculations in Strip Rolling Process", Journal of the Material Shaping Technology, 8 (1990) 167-177.
[8] D. Rusia, "Review and Evaluation of Different Methods for Force and Torque Calculations in the Strip Rolling Process", Journal of the Material Shaping Technology, 9 (1991) 117-125.
[9] W. Johnson and G. Needham, "An Experimental Study of Asymmetrical Rolling", Applied Mechanics Convention, Cambridge, Instn. Mech. Engrs., 180 (April 1966) 270-281.
[10] W. Johnson and G. Needham, "Further Experiments In Asymmetrical rolling", Int. J. Mech. Sci., 8 (February 1966) 433-455.
[11] I. F. Collins and P. Dewhurst, "A Slipline Field Analysis of Asymmetrical Hot Rolling", Int. J. Mech. Sci., 17 (1975) 643-651.
[12] Janusz Popiech, "A note on the influence of some factors affecting curvature in the flat rolling of strip", Journal of Mechanical Working Technology. 15 (1987) 69-80.
[13] J. Jeswiet, P.G.Greene, "Experimental measurement of curl in rolling", J. Mater. Proces. Technol., 84, (1998) 202-209.
[14] Campbell McConnell and J.G. Lenard, "Friction in cold rolling of a low carbon steel with lubricants", Journal of Materials Processing Technology. 99 (2000) 86-93.
[15] H.Dyja, J.Markowski, D.Stoninski, "Asymmetry of the roll gap as a factor improving work of the hydraulic gauge control in the plate rolling mill", Journal of Materials Processing Technology,60 (1996) 73-80.
[16] M.Salimi, F.Sassanib, "Modifed slab analysis of asymmetrical plate rolling", International Journal of Mechanical Sciences, 44 (2002) 1999–2023.
[17] J. Markowski, H. Dyja, M. Knapinski, A. Kawalek, "Theoretical analysis of the asymmetric rolling of sheets on leader and finishing stands", Journal of Materials Processing Technology, 138 (2003) 183-188.
[18] A. Kawalek, "Forming of Band Curvature in Asymmetrical Rolling Process", Journal of Materials Processing Technology, 155-156 (2004) 2033-2038.
[19] A. Kawalek, "The Theoretical and Experimental Analysis of The Effect of Asymmetrical Rolling on The Value of Unit Pressure", Journal of Materials Processing Technology, 157-158(2004) 531-535.
[20] F.Farhat-Nia, M.Salimi, M.R.Movahhedy, "Elasto-plastic finite element simulation of asymmetrical plate rolling using an ALE approach", Journal Materials Processing Technology, 177 (2006) 525-529,
[21] 孟繼洛, "機械材料", 臺北市:曉園出版社, (1990) 430-431。
[22] Designation：E8M, Standard Test Methods for Tension Testing of Metallic Materials [Metric], pp. 85.
[23] W. F. Hosford and M. C. Caddell, "Metal forming Mechanics and Metallurgy", Prentice-Hall International Inc., (1993) 55-60.
[24] A. T. Male and M. G. Cockcroft, "A Method for the Determination of the Coefficient of Friction of Metals under Conditions of Bulk Plastic Deformation", Journal of the Institute of Metals, 93 (1964-65) 38-46.
[25] J. G. Lenard, "Friction and Forward Slip in Cold Strip Rolling", Tribology Transactions, 35 (1992) 423-428.

指導教授

葉維磬(Wei-Ching Yeh)

審核日期

2008-7-23

推文