入口角度對非對稱壓延A1050P鋁材彎曲行為之實驗研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：80

、訪客IP：3.15.231.65

姓名

詹敏雄(Min-Hsiung Chan) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

入口角度對非對稱壓延A1050P鋁材彎曲行為之實驗研究
(Experimental research of entry angle effect curvature behavior of asymmetrical rolling aluminum A1050P)

相關論文

★ 中尺寸LED背光模組之實驗研究	★ 利用有限元素法與反應曲面法探討金屬成型問題之最佳化設計-行星路徑旋轉鍛造傘齒輪為例
★ 以反應曲面法進行行動電話卡勾之最佳化設計	★ 以微分式內涵塑性理論分析材料受軸向循環負載之塑性行為
★ A1070在累進式背擠製下的機械性質與微結構之研究	★ 超音波輔助沖壓加工之應用-剪切、引伸與等通彎角擠製
★ 應用多體動力學於具循環氣體負載之迴轉式壓縮機振動預測模型建立	★ 以有限元素法與反應曲面法分析螺旋傘齒輪之旋轉鍛造最佳化設計
★ 超音波振動輔助鋁合金6061及低碳鋼S15C拉伸試驗之研究	★ 旋轉鍛造螺旋齒輪製程分析
★ 等通道扭轉彎角擠製之有限元素法及反應曲面法分析	★ 以有限元素法與反應曲面法分析增量式板金成形
★ 以有限元素法與反應曲面法分析螺旋傘齒輪之雙錐輥旋轉鍛造最佳化設計	★ 以有限元素法與反應曲面法分析兩點增量成形
★ 引伸成形加工問題之有限元素分析	★ 應用流函數法分析軸對稱熱擠製加工問題

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

由於非對稱壓延可有效降低壓延力及壓延扭矩，使材料於壓延製
程安排上，更趨自由與多樣性，在壓延工業之應用上，具有極大之助益；但於非對稱壓延後之板材易產生彎曲現象而造成產品品質降低及設備損壞。
本文主要以實驗的方法，觀察A1050P鋁材接觸輥輪時之入口角度
不同，對壓延後之板材彎曲曲率的變化情形，探討曲率與上下輥輪切線速度比值、縮減率及界面摩擦條件之關係，並討論加工參數對壓延力和壓延扭矩之影響。期望藉由本文所得之實驗結果，可提供理論解析之驗證及非對稱壓延製程品質改善之參考。

摘要(英)

Due to the asymmetrical rolling can reduce rolling force
and rolling torque that will make rolling process also flexible and variable. There are extreme advantages in application of rolling industry. The specimens will curvature after the asymmetrical rolling, the flat bending will reduce production quality and impact machine.
This research mainly use experiment to observe curvature
about aluminum flat A1050P at rolling mill with different
concact entry angle after rolling, investigate curvature
behavior with mismatch peripheral speed ratio, reduction,
interface friction, also discuss rolling force and rolling
torque with process parameter. The results will supply theory, numeral analysis and process quality improvement.

關鍵字(中)

★ 壓延
★ 入口角度
★ 曲率

關鍵字(英)

★ rolling
★ entry angle
★ curvature

論文目次

中文摘要 I
Abstract II
誌謝 III
總目錄 IV
圖目錄 VI
表目錄 IX
第一章緒論 1
1-1 前言 1
1-2 板材非對稱壓延 2
1-3 研究動機 3
第二章壓延基礎 4
2-1 壓延種類 4
2-2 文獻回顧 5
2-2-1 實驗研究方面 5
2-2-2 理論解析方面 7
第三章實驗設備與方法 11
3-1 實驗設備 11
3-1-1 壓延機 11
3-1-2 資料擷取系統 12
3-2 實驗方法 12
3-2-1 試片規格與準備 12
3-2-2 非對稱壓延實驗條件 13
3-2-3 潤滑條件 14
3-2-4 編號的表示意義 14
3-2-5 輥論及工作平台之調整 15
3-2-6 壓延實驗步驟 16
3-3 成形試片之曲率量測 17
3-3-1 曲率計之測定原理 17
3-3-2 曲率量測方法之探討 18
3-3-3 曲率計之校正 18
3-4 拉伸試驗 19
3-5 環壓試驗 20
第四章結果與討論 23
4-1 拉伸試驗 23
4-2 環壓試驗 23
4-3 壓延實驗 24
4-3-1 壓延力及壓延扭矩之比較 25
4-3-2 周速比對壓延試片曲率之效應 27
4-3-3 入口角度對於同徑同周速成形試片彎曲曲率的影響 30
4-3-4 入口角度對於同徑異周速成形試片彎曲曲率的影響 31
4-3-5 界面摩擦應力對成形試片彎曲曲率的效應 32
第五章結論 36
參考文獻 38
附錄 A 70
附錄 B 78
附錄 C 80

參考文獻

[1] T. von Karman, Zeitschrift fur angewandte Mathematik und Mechanik, 5 (1925) 139.
[2] E. Orowan, The Calculation of Roll Pressure in Hot and Cold Flat Rolling, Proceedings of the Institution of Mechanical Engineers, 150 (1943) 140-167.
[3] D. R. Bland and H. Ford, The Calculation of Roll Force and Torque in Cold Strip Rolling with Tensions, Proc. Instn. Mech. Engrs., 159 (1948) 144-153.
[4] H. Ford, F. Ellis and D. R. Bland, Cold Rolling with Strip Tension Part I. A New Approximate Method of Calculation and a Comparison with Other Method, Journal of the Iron and Steel Institute, May, (1951) 57-72,.
[5] R. B. Sims, The Calculation of Roll Force and Torque in Hot Rolling Mills, Proc. Instn. Mech. Engrs., 168 (1954) 191-200.
[6] J. M. Alexander, On the Theory of Rolling, Proceedings of the Royal Socity of London. Series A, 326 (1972) 535-563.
[7] D. Rusia, Improvements to Alexander's Computer Model for Force and Torque Calculations in Strip Rolling Process, Journal of the Material Shaping Technology, 8 (1990) 167-177.
[8] D. Rusia, Review and Evaluation of Different Methods for Force and Torque Calculations in the Strip Rolling Process, Journal of the Material Shaping Technology, 9 (1991) 117-125.
[9] W. Johnson and G. Needham, An Experimental Study of
Asymmetrical Rolling, Inst. of Mech. Sci., 8 (1966) 448-455.
[10] I. F. Collins and P. Dewhurst, A Slipline Field Analysis of Asymmetrical Hot Rolling, Int. J. Mech. Sci., 17 (1975) 643-651.
[11] J. Jeswiet and P. G. Greene, Experimental Measurement of Curl in Rolling, J. Mater. Proces. Technol., 84 (1998) 202-209.
[12] M. Salimi and F. Sassanib, Modifed Slab Analysis of Asymmetrical Plate Rolling, International Journal of Mechanical Sciences, 44 (2002) 1999–2023.
[13] H. Dyja, P.Korczak and J.W.Pilarczyk, J. Grzybowski, Theoretical and Experimental Analysis of Plates Asymmetric Rolling, Journal of Materials Processing Technology, 45 (1994) 167-172
[14] H. Dyja, J. Markowski and D. Stoninski, Asymmetry of the Roll Gap as a Factor Improving Work of the Hydraulic Gauge Control in the Plate Rolling Mill, Journal of Materials Processing Technology, 60 (1996) 73-80.
[15] J. -S. Lu, O. -K. Harrer, W. Schwenzfeier and F. D. Fischer, Analysis of the Bending of the Rolling Material in Asymmetrical Sheet Rolling, International Journal of Mechanical Sciences, 42 (2000) 49-61.
[16] J. Markowski, H. Dyja, M. Knapinski and A. Kawalek, Theoretical Analysis of the Asymmetric Rolling of Sheets on Leader and Finishing Stands, Journal of Materials Processing Technology, 138 (2003) 183-188.
[17] A. Kawalek, Forming of Band Curvature in Asymmetrical Rolling Process, Journal of Materials Processing Technology, 155-156 (2004) 2033-2038.
[18] A. Kawalek, The Theoretical and Experimental Analysis of The Effect of Asymmetrical Rolling on The Value of Unit Pressure, Journal of Materials Processing Technology, 157-158 (2004) 531-535.
[19] M. philipp, W. Schwenzfeier, F. D. Fischer, R. Wodlingre and C. Fischer, Front End Bending in Plate Rolling Influenced by Circumferential Speed Mismatch and Geometry, Journal of Materials Processing Technology, 184 (2007) 224-232.
[20] 孟繼洛,”機械材料”, 臺北市:曉園出版社, (1990) 430-431。
[21] A. T. Male and M. G. Cockcroft, A Method for the Determination of the Coefficient of Friction of Metals under Conditions of Bulk Plastic Deformation, Journal of the Institute of Metals, 93 (1964-65) 38-46.
[22] Designation：E8M, Standard Test Methods for Tension Testing of Metallic Materials [Metric], 85.
[23] W. F. Hosford and M. C. Caddell, Metal forming Mechanics and Metallurgy, Prentice-Hall International Inc., (1993) 55-60.

指導教授

葉維磬(Wei-Ching Yeh)

審核日期

2008-7-22

推文