脈衝電化學加工之微電極製作參數分析

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：65

、訪客IP：3.141.25.214

姓名

王正育(Cheng-Yu Wang) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

脈衝電化學加工之微電極製作參數分析
(The Analysis and Investigation on the Micro-electrode Fabrication by Pulses Electrochemical Machining)

相關論文

★ 迴轉式壓縮機泵浦吐出口閥片厚度對性能影響之研究	★ 鬆弛時間與動態接觸角對旋塗不穩定的影響
★ 電化學製作針錐微電極之製程研究與分析	★ 蚶線形滑轉板轉子引擎設計與實作
★ 利用視流法分析金屬射出成形脫脂製程中滲透度與毛細壓力之關係	★ 應用離心法實驗探求多孔介質飽和度與毛細力之關係
★ 利用網絡模型數值模擬粉末射出成形製程毛細吸附脫脂機制	★ 轉注成形充填過程之巨微觀流數值模擬
★ 二維熱流效應對電化學加工反求工具形狀之分析	★ 金屬粉末射出成形製程中胚體毛細吸附脫脂之數值模擬與實驗分析
★ 飽和度對金屬射出成形製程中毛細吸附脫脂之影響	★ 轉注成型充填過程巨微觀流交界面之數值模擬
★ 轉注成型充填過程中邊界效應之數值模擬	★ 鈦合金整流板電化學加工技術研發
★ 射出/壓縮轉注成型充填階段中流場特性之分析	★ 脈衝電化學加工過程中氣泡觀測與分析

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

在發展微機電系統過程中，製作微結構產品的加工方法是重要且必須的，其中微電化學加工具有可加工任何金屬材料，工件表面無殘留應力，工具電極不損耗等優勢。在微電化學加工中，需要更微細工具電極，方可製造微結構元件，故本文將以製作圓柱狀的微電極為目標。
　　本文利用單一因子法分析加工參數(如：操作電壓、電解液濃度、脈衝頻率、加工能率、電解液溫度、電極旋轉速度)，再以單一因子法分析的結果；作為第二部份線性變化(如：操作電壓、加工能率)的實驗依據。
　　最後本文利用510 μm的鎢棒，以線性遞減操作電壓和加工能率的方式，成功的製作出刃長為2㎜、3㎜、4㎜，電極直徑為100 μm的圓柱狀微電極。

摘要(英)

The development of MEMS (Micro Electro-Mechanical System), it is important and necessary to manufacture the micro-structure. In numerous of micro machining, the electrochemical micro machining has advantage that can machining any metal material, the work piece after machining will not have any residual stress remained on its surface, the tool electrode would not break. In the electrochemical micro machining, it needs the smaller electrode to manufacture the micro electrode. On the basis of advantage of electrochemical machining, we applied in the form of pulsed electrochemical polishing to fabricate the cylindrical microelectrode. We discussed the working parameters (ex. applied voltage, electrolyte concentration, frequency, duty, temperature, rotation) on fabricating microelectrode, and then it could fabricate the 100 μm cylindrical tungsten microelectrode by linear decay of applied voltage or duty at different length.

關鍵字(中)

★ 微電化學加工
★ 鎢棒
★ 脈衝電壓
★ 微電極

關鍵字(英)

★ Tungsten rod
★ Micro electrode
★ pulsed voltage
★ Electrochemical micromachining

論文目次

摘要 I
Abstract II
表目錄 VI
圖目錄 VII
符號說明 XI
第一章緒論 1
1-1 前言 1
1-2 電化學加工 4
1-2-1 電化學拋光 6
1-3 文獻回顧 7
1-3-1 微電極製作 7
1-3-2 電化學加工 10
1-4 研究目的 14
第二章理論基礎 17
2-1 電化學加工基本理論 17
2-1-1 電流分佈 18
2-1-2 電流效率與電流密度 18
2-1-3 液相質傳動力學 19
2-1-4 電解液導電度 22
2-1-5 電化學拋光原理 23
2-2 電化學反應式 26
2-3 極化(polarization) 28
2-4 旋轉圓柱電極之極限電流 30
第三章實驗裝置與步驟 32
3-1實驗設備 32
3-1-1 機台結構設計 32
3-1-2 刀具進給控制系統 33
3-1-3 脈衝電源供應系統 34
3-1-4 伺服馬達 34
3-2 實驗材料 35
3-2-1 陰極導引片 35
3-2-2 陽極電極刀具 35
3-2-3 氫氧化鈉粉末 36
3-3 實驗步驟及注意事項 36
4-1 操作電壓 43
4-2 電解液濃度 46
4-3 脈衝頻率 48
4-3-1 脈衝週期(固定脈衝放電時間，改變脈衝週期) 48
4-3-2 脈衝頻率(固定加工能率，改變脈衝頻率) 50
4-4 加工能率(Duty) 52
4-4-1 高加工能率 52
4-4-2 低加工能率 55
4-5 電解液溫度 58
4-6 電極旋轉速度 59
4-7 操作電壓之線性變化加工 63
4-8 加工能率之線性變化加工 65
4-9 實驗成果 66
第五章結論 70
5-1 結論 70
5-2 未來展望 71
參考文獻 73
附表 77
附圖 78

參考文獻

1. D.J. Nagel and M.E. Zaghloul , MEMS : Micro Techanology : Mega Impact, IEEE Circuit Devices Magazine. Vol. 28, pp. 14-25 (2001).
2. Nadim Maluf著，李世鴻譯著，微機電系統工程，五南圖書(2003)
3. 陳炳煇編著，微機電系統，五南圖書(2001)
4. D. Zhu1, K. Wang and N. S. Qu, Micro Wire Electrochemical Cutting by Using in Situ Fabricated Wire Electrode, CIRP Annals - Manufacturing Technology Vol.56, pp.241-244 (2007)
5. J.A. McGeough, Principles of Electrochemical Machining, Chapman Hall, London. 1974.
6. S. H. Ahn, S. H. Ryu, D. K. Choi and C. N. Chua, Electro-chemical Micro Drilling Using Ultra Short Pulses, Precision Engineering.Vol. 28, pp. 129-34 (2004).
7. Xu Jiawena, Yun Naizhang, Tang Yangxin and K.P. Rajurkar, The modelling of NC-electrochemical contour evolution machining using a rotary tool-cathode, Journal of Materials Processing Technology Vol. 159 pp.272–277 (2005).
8. 木本康雄著，賴耿陽譯著，精密加工之電學應用，復漢出版社(1982).
9. 佐藤敏一著，賴耿陽譯著，金屬腐蝕加工技術，復漢出版社(1986).
10. 賀陳弘、魏水文、巴白山，電化學拋光技術，機械工業雜誌，170 期，122-128頁，5月，1997。
11. Y. M. Lim and S. H. Kim, An Electrochemical Fabrication Method for Extremely Thin Cylindrical Micropin, International Journal of Machine Tools & Manufacture, Vol. 41, pp. 2287-2296 (2001).
12. Y. M. Lim, H. J. Lim, J. R. Liu and S. H. Kim, Fabrication of Cylindrical Micropins with Various Diameters Using DC Current Density Control, Journal of Materials Processing Technology, Vol. 141, pp. 251-255 (2003).
13. Z. Wang, B. Zhu and G. Cao, Fabricating Microelectrode by Electrochemical Micromachining, Proceedings of SPIE, Vol.6041, pp.1-5 (2006).
14. S. H. Choi, S.H. Ryu and C.N. Chu, Fabrication of WC Micro-shaft By Using Electrochemical Etching, International Journal of Advanced Manufacture Technology, Vol. 31, pp. 682-687 (2007).
15. E. S. Lee, S. Y. Baek, and C. R. Cho, A study of The Characteristics for Electrochemical Micromachining with Ultrashort Voltage Pulses, International Journal of Advanced Manufacture Technology, Vol. 31, pp. 762-769 (2007).
16. R. Hobara, S. Yoshimoto, and S. Hasegawa, Dynamic Electrochemical Etching Technique for Tungsten Tips Suitable for Multi-tip Scanning Tunneling Microscopes, Journal of Surface Science and Nanotechnology, Vol. 5, pp. 94-98 (2007).
17. R. Maeda, K. Chikamori and H. Yamamoto, Feed Rate of Wire Electrochemical Machining Using Pulsed Current, Precision Engineering, Vol. 31, pp. 193-199 (1984).
18. Rolf Schuster and Viola Kirchner, Philippe Allongue, Electrochemical Micro- Machining, Science, Vol. 289, No. 5, pp. 98-101 (2000).
19. B. Bhattacharyya and J. Munda, Experimental Investigation on the Influent of Electrochemical Machining Parameters on Machining Rate and Accuracy in Micromachining Domain, International Journal of Machine Tool and Manufacture, Vol. 43, pp. 1301-1310 (2003).
20. M. Kock, V. Kirchner and R. Schuster, Electrochemical Micromachining with Ultrashort Voltage Pulses a Versatile Method with Lithographical Precision, Electrochemical Action Vol. 48, pp. 3213-3219 (2003).
21. Y. Li, Y. Zheng, G. Yang and L. Q. Peng, Localized Electrochemical Micromachining with Gap Control, Sensors and Actuators, A 108, pp. 144-148 (2003).
22. B. H. Kim, S. H. Ryu, D. K. Choi, and C. N. Chu, Micro Electrochemical Milling, Journal of Micromechanics and Microengineering, Vol. 15, No. 1, pp. 124-129 (2004).
23. H. Hocheng,Y. H. Sun, S. C. Lin and P.S. Kao, A Material Removal Analysis of Electrochemical Machining Using Flat-End Cathode, Journal of Material Processing Technology, Vol. 140, pp. 264-268 (2003).
24. P. Allongue, P. Jiang, V. Kirchner, A. L. Trimmer and R. Schuster, Electrochemical Micromachining of p-Type Silicon, Journal of Physical Chemistry B, Vol. 108, pp. 14434-14439 (2004).
25. B. Bhattacharyya , M. Malapati and J. Munda, Advancement in Electrochemical Micro-machining, Journal of Materials Processing Technology, Vol. 169, pp. 485-492 (2005).
26. T. Kurita, K. Chikamori, S. Kubota and M. Hattori, A Study of Three-dimensional Shape Machining with an ECμM system, International Journal of Machine Tools & Manufacture, Vol. 46, pp. 1311-1318 (2006).
27. B. Bhattacharyya, M. Malapati, J. Munda and A. Sarkar, Influence of Tool Vibration on Machining Performance in Electrochemical Micro-machining of Copper, Journal of Materials Processing Technology, Vol.47, pp. 335-342 (2007).
28. M. S. Park and C. N. Chu, Micro-electrochemical Machining Using Multiple Tool Electrodes, Journal of Micromechanics and Micro-engineering, Vol. 17, No. 8, pp. 1451-1457 (2007).
29. J. A. Kenney and G.S. Hwang, Electrochemical Machining with Ultra Voltage Pulses: Modeling of Charge Dynamics and Feature Profile Evolution, Nanotechnology, Vol. 16, pp. S309-S313 (2005).
30. J. A. Kenney and G.S. Hwang, Etch Trends in Electrochemical Machining with Ultrashort Voltage Pulses, Electrochemical and Solid-State Letters, Vol. 9, No. 1, pp. D1-D4 (2006).
31. J. A. Kenney and G.S. Hwang, Computational Analysis of Intratool Interactions in Electrochemical Micromachining with Multitip Tool Electrodes, Electrochemical and Solid-State Letters, Vol. 9, No. 9, pp. D21-D23 (2006).
32. Y. F. Luo, Differential Equation for the Ultra-Fast Transient Migration in Electrolytic Dissolution, Electrochemistry Communications, Vol. 8, pp. 353-358 (2006).
33. M. Datta and D. Landolt, Fundamental Aspects and Applications of Electrochemical Microfabrication, Electrochemical Acta, Vol.45, pp. 2535–2558 (2000).
34. 楊顯謀，不銹鋼電解拋光技術簡介，鋼鐵研究，72 期，84-96頁，12 月，1989。
35. H. Hocheng and P.S. Pa, Electropolishing and Electrobrightening of Holes Using Different Feeding Electrodes, Journal of Materials Processing technology. Vol. 89-90, pp. 440-446 (1999).
36. 陳裕豐，高潔淨閥件之流道表面處理－電解拋光（EP）技術，機械工業雜誌，198 期， 230-240頁，9 月，1999。
37. Nikolova, M. S., Natarajan, A. and Searson, P. C. , Electrochemical Fabrication of Sharp Nickel Tips in H2SO4 Solutions, Journal of the Electrochemical Society. Vol. 144, NO. 2, pp. 455-460 (1997).
38. G.J Edwards and P.R. Pearce, Comparison of AC and DC Electrochemical Etching Techniques for the Fabrication of Tungsten Whiskers, Journal of Physics. Vol. 11, pp. 761-764 (1978).
39. 胡啟章編著，電化學原理與方法，五南圖書 (2002).
40. J. L. Stojak and J. B. Talbot, Effect of Particles on Polarization During Electro-Deposition Using A Rotating Cylinder Electrode, Journal of Applied Electrochemistry, Vol. 31, pp. 559-564 (2001).
41. J.F. Thorpe and R.D. Zerkle, Theoretical Analysis of the Equilibrium Sinking of Shallow, Axially Symmetric, Cavities by Electrochemical Machining, Electrochemical Society Princeton pp.1-39(1971).

指導教授

洪勵吾(Lih-Wu Hourng)

審核日期

2008-6-25

推文