電化學放電加工應用於石英玻璃之研究與分析 ; The Study of Drilling on Quartz by Electrochemical Discharge Machining

NCU Institutional Repository > 工學院 > 機械工程研究所 > 博碩士論文 > Item 987654321/46338

jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/46338

题名:	電化學放電加工應用於石英玻璃之研究與分析;The Study of Drilling on Quartz by Electrochemical Discharge Machining
作者:	林愈森;Yu-sen Lin
贡献者:	機械工程研究所
关键词:	石英玻璃;電化學放電加工;Quartz;Electrochemical Discharge Machining
日期:	2010-12-14
上传时间:	2011-06-04 15:01:07 (UTC+8)
出版者:	國立中央大學
摘要:	隨著微機電系統的發展，光學玻璃與石英等非導電材料的應用遽增，電化學放電加工是非導電硬脆材料加工製程的新興技術，具有相當的發展潛力和高附加價值。本文採用直徑100μm之碳化鎢作為刀具，氫氧化鉀為電解液，對石英玻璃進行電化學放電加工，以單一因子法分析各加工參數（如：操作電壓、電解液濃度、脈衝頻率、加工能率、電流波形、進給速率）之影響；並利用田口實驗方法分析加工參數（如：操作電壓、電解液濃度、脈衝頻率、加工能率）的相對重要性。實驗結果顯示，由單一因子法得知，最佳參數偏向於低的操作電壓、低電解液濃度以及較高的脈衝頻率。分析出之結果最佳參數分別為加工電壓40V、加工能率20％、電解液濃度20％、脈衝頻率100 KHz；由田口法得知，操作電壓大小對於加工孔徑影響最大，貢獻率達59.84％；並且以最佳參數進行加工，得到加工孔徑約 166μm。最後本文在電解液內加入肥皂水，成功的減少氣泡膜成長時間，孔徑過切量降至143μm。 The optical materials such as Pyrex and quartz are widely used with enormous potentialities and highly added value. However, the machining of non-conductive brittle materials is remaining as a big concern. The new developed technology, electrochemical discharge machining (ECDM), is a promising process for machining non-conductive brittle materials. In present thesis quartz is machined by ECDM. A tungsten carbide cylinder with diameter of 100 micro-meters is selected as the electrode tool. KOH is selected as the electrolyte. In this research, the single variable method and Taguchi statistical method are used to analyze the influence of the parameters(such as applied voltage, concentration of electrolyte, pulse frequency, duty, current waveform, tool feeding rate, etc) on the over cut of the drilling and the relative importance among parameters. From experimental results, it shows that applied voltage has relatively large influence on machining. The optimal parameters are taken for drilling the quartz, and a hole with diameter of about 166 μm is obtained. Finally, it is successful in reducing the gas film thickness when the liquid soap is added to mix with the KOH electrolyte, and the hole with diameter of about 143 μm is obtained.
显示于类别:	[機械工程研究所] 博碩士論文

文件中的档案:

档案	描述	大小	格式	浏览次数
index.html		0Kb	HTML	762	检视/开启

在NCUIR中所有的数据项都受到原著作权保护.

社群 sharing

数据加载中.....