中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/68891
English  |  正體中文  |  简体中文  |  全文笔数/总笔数 : 69561/69561 (100%)
造访人次 : 23194664      在线人数 : 1035
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜寻范围 查询小技巧:
  • 您可在西文检索词汇前后加上"双引号",以获取较精准的检索结果
  • 若欲以作者姓名搜寻,建议至进阶搜寻限定作者字段,可获得较完整数据
  • 进阶搜寻


    jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/68891


    题名: 應用磁耦合變壓器技術之雙頻帶金氧半導體壓控振盪器暨5 GHz壓控振盪器與除頻器整合電路;CMOS Voltage Controlled Oscillator with Magnetically Coupled Transformer Switch for Dual-band Application and 5 GHz VCO and Divider Integrated Circuit
    作者: 戴瑋佑;Dai,Wei-you
    贡献者: 電機工程學系
    关键词: 壓控振盪器;雙頻;除頻器;VCO;Dual band;divider
    日期: 2015-08-04
    上传时间: 2015-09-23 14:46:04 (UTC+8)
    出版者: 國立中央大學
    摘要: 本文利用tsmcTM 0.18 m製程技術來進行本地振盪源電路的相關設計;本論文探討現今雙頻操作振盪器的機制,設計運用磁耦合變壓器切換技術達到雙頻操作的壓控振盪器,結合不同的架構達到低功耗、低相位雜訊的目標,同時以實作的量測結果,驗證電路理論設計之正確性。其設計內容包含三個電路,內容如下所述:
    一、應用磁耦合變壓器切換技術之寬頻壓控振盪器之研製
    利用磁耦合變壓器切換技術,可以縮減面積以及讓調頻的頻率逐步遞增,電路的調頻範圍可以從5.55 GHz調到10.26 GHz,相位雜訊在偏移1 MHz處為-105.71 dBc/Hz,電路功耗為3.2 mW,電路的優化指標(FoMT)為-192.18;晶片面積為0.752 × 0.8 mm2。
    二、雙模態考畢茲電流再利用壓控振盪器之研製
    本電路結合磁耦合變壓器切換的技術以及考畢茲、電流再利用的架構,加入源極退化電感,以增加可調頻寬以及簡化直流偏壓設計。兩個頻段的可調頻率範圍分別為5.24 GHz – 5.48 GHz以及10.4 GHz – 11.55 GHz,功耗為1.95 mW,相位雜訊在偏移1 MHz的地方為-114.9以及 -105.35 dBc/Hz,電路的優化指標在兩個頻段分別為-185.1以及-183.38;整體的晶片面積為0.842 × 0.732 mm2。
    三、5 GHz壓控振盪器暨除頻器整合電路
    本電路包含一顆寬頻與低相位雜訊的壓控振盪器以及改良後的電流模態除頻器;壓控振盪器的可調頻率範圍為4.68 GHz – 6.19 GHz,對應的除頻範圍為2.34 GHz – 3.1 GHz,直流功耗為2.52 與3.75 mW;相位雜訊在偏移1 MHz的地方為-117.1 以及-122.3 dBc/Hz。整體的晶片面積為0.73 × 1.16 mm2。
    ;As more increasing demands for low-cost in wireless communication system, multi-standards circuits are proposed to support the requirements. Therefore, RF transceivers become more complex and consume more power to satisfy the different wireless systems, which means that various kinds of local sources are needed meanwhile. Since voltage controlled oscillator (VCO) is an important sub-circuit in phase locked loop (PLL), this thesis includes five parts, which are motivation, two VCOs for dual-band application, integrated circuits for 5GHz and future work.
    Chapter 1 illustrates the motivation of the system standards. And chapter 2 introduces the basic theory of transformer and implements a transformer-switch based VCO for dual-band and wideband application fabricated in 0.18-μm CMOS technology. This design uses the transformer not only for reducing the chip size, but also enabling the center frequency tunable monotonically. By setting the different bias, the circuit can be operated as dual-band or wideband. The measured tunable oscillation frequency is from 5.55 GHz to 10.26 GHz. The power consumption is 3.2 mW and the phase noise is -105.71 dBc/Hz at 1-MHz offset respectively. The obtained FoMT is -192.18. The chip area, including RF signal pads and DC bias pads, is 0.752 × 0.8 mm2.
    Chapter 3 presents a Colpitts with current-reused technology. The Colpitts current-reused VCO fabricated in 0.18-μm CMOS technology with magnetically coupled switch. The design procedure and measurements are described in this chapter. This circuit adopts the source degeneration inductor to extend the tuning range and eases the design of DC bias simultaneously. The measured center frequencies for each sub-band are 5.36 GHz and 10.95 GHz with tunable from 5.24 GHz to 5.48 GHz and 10.4 GHz to 11.5 GHz. The phase noise are -114.9 and -105.35 dBc/Hz, respectively. The total power consumption is 1.95 mW. The FoM are -185.1 and -183.38, respectively. The chip area, including RF signal pads and DC bias pads, is 0.842 × 0.732 mm2.
    Chapter 4 then reviews the conventional design of frequency dividers. A VCO is integrated with frequency divider in this chapter. The oscillator can be tuned from 4.68 GHz to 6.19 GHz, the corresponding output frequency of divider is 2.34 GHz to 3.1 GHz. The power consumptions are 2.52 and 3.75 mW. The phase noise are -117.1 and -122.3 dBc/Hz respectively. The chip area, including RF signal pads and DC bias pads, is 0.73 × 1.16 mm2.
    Chapter 5 concludes the aforementioned three designs and brings up the future work in the end of the thesis.
    显示于类别:[電機工程研究所] 博碩士論文

    文件中的档案:

    档案 描述 大小格式浏览次数
    index.html0KbHTML336检视/开启


    在NCUIR中所有的数据项都受到原著作权保护.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 回馈  - 隱私權政策聲明