大功率散熱鰭片之熱傳分析

NCU Institutional Repository > 工學院 > 機械工程學系碩士在職專班 > 博碩士論文 > Item 987654321/95877

請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/95877

題名:	大功率散熱鰭片之熱傳分析
作者:	黃浩彰;Huang, Hao-Jhang
貢獻者:	機械工程學系在職專班
關鍵詞:	強制對流;thermal analysis;Heat Sink
日期:	2024-07-30
上傳時間:	2024-10-09 17:21:28 (UTC+8)
出版者:	國立中央大學
摘要:	電力電子產品不斷追求高功率密度設計，但並非每個產品都能使用水冷散熱。在實際應用中，信賴性、維修便利性以及客戶需求等因素都需要考量。因此，對氣冷散熱器進行優化在實務設計中是必要的。此外，對於大功率機種，重量和成本也往往是設計需求中的重要考量因素。本研究針對固定體積下的散熱鰭片進行分析。研究對象的整體高度為90mm，總寬度為204mm，長度為90mm。單一熱源的發熱量為720W，共有兩個熱源。該散熱模組使用兩顆9038 風扇。在有限的空間下，通過優化散熱片的幾何參數和散熱鰭片的傾角特徵進行設計。結果顯示，在有熱管的前提下，改變散熱片底部厚度對特性影響不顯著。而在鰭片間距固定的情況下，增加散熱片厚度對特性的改善有顯著幫助。在可變鰭片的條件下，鰭片間距與鰭片厚度的比值在2 到3 之間時，可達到最佳設計效果。前置傾角對風扇壓降的改善較為顯著，在45 度傾角條件下，特性接近於無傾角情況。後置傾角容易增加系統壓降，進而影響風扇整體流量，對特性無顯著幫助。中置傾角會稍微增加部分壓降，但有助於改善散熱片溫升。優化之結果約可改善57%重量並維持相同特性。;Power electronic products continuously strive for high power density designs; however, not every product can employ liquid cooling solutions. In practical applications, factors such as reliability, ease of maintenance, and customer requirements must be considered. Therefore, optimizing air-cooled heat sinks is necessary from a practical standpoint. Additionally, for high-power models, weight and cost are often critical design considerations. This study heat sinks within fixed dimensions. The overall height is 90mm, the total width is 204mm, and the length is 90mm. Each heat source generates 720W, with two heat sources in. The heat dissipation module with two 9038 fans. Within the limited space, the heat sink design is optimized by adjusting the geometric parameters and inclination angles of the fins. The results show that with heat pipes, changing the base thickness of the heat sinks has no significant impact on performance. When the fin spacing is fixed, increasing the thickness of the heat sinks significantly improves performance. Under conditions with variable fins, the optimal ratio of fin spacing to fin thickness is between 2 and 3. The pre-angled fins significantly improve the fan pressure drop, with characteristics close to those of non-angled fins at a 45-degree angle. The post-angled fins tend to increase the system pressure 4 drop, thereby affecting the overall airflow of the fan, and provide no significant benefit to performance. The mid-angled fins slightly increase the pressure drop but are expected to improve the temperature rise of the heat sinks. The optimized parameters proposed in this study improve performance by approximately 57%.and keep the same temperature.
顯示於類別:	[機械工程學系碩士在職專班 ] 博碩士論文

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	38	檢視/開啟

在NCUIR中所有的資料項目都受到原著作權保護.

社群 sharing

資料載入中.....